2 Row Aluminum Radiator For 1990-97 Toyota MR2 MR-2 SW20 2.0 REV1 REV2 REV3 TURB

  
OE design to ensure exact fit, form and function for an easy drop-in installation. Built with high density multi-lowered fins for maximum cooling efficiency. ISO 9001 certified manufacturing plants.

Plastic tanks with aluminum core. Built to strict quality control standards. DIRECT FIT FIT NISSAN 300ZX V6 3.0L 1996 1995 1994 1993 1992 1991 1990 FIT NISSAN MAXIMA V6 3.0L 1994 1993 1992 1991 1990 1989.

FIT NISSAN 300ZX 1996 FIT NISSAN 300ZX 1995 FIT NISSAN 300ZX 1994 FIT NISSAN 300ZX 1993 FIT NISSAN 300ZX 1992 FIT NISSAN 300ZX 1991 FIT NISSAN 300ZX 1990. FIT NISSAN MAXIMA 1994 FIT NISSAN MAXIMA 1993 FIT NISSAN MAXIMA 1992 FIT NISSAN MAXIMA 1991 FIT NISSAN MAXIMA 1990 FIT NISSAN MAXIMA 1989. Start the vehicle, to rise to normal temperature. Slowly open the tank cover, the fluid shake from the tank after filling the mouth, the cleaner can be mixed with any brand of coolant.

Idle running not less than 15 minutes, not cleaning vehicles not less than 30 minutes for two years. And then discharge coolant, flush water tank, until out of clear water, suitable for any water cycle system.

After cleaning, after waiting for pipeline rehabilitation add fluid to water tank, and inject new coolant and water purification. How to replace the radiator.

Drain the radiator fluid into a suitable container. Take off any plastic covers around the radiator. Disconnect the electrical connector to the fan, and unbolt and remove the fan assembly.

Disconnect the radiator hoses from the radiator. Disconnect the transmission cooling lines from the bottom of the radiator. Remove any clamps, brackets, or screws holding the radiator inside its frame. Lift the radiator up and out of the car. Slide the new radiator into place.

Connect any clamps or brackets that hold the radiator in place. Connect the transmission cooling lines carefully. Connect the engine cooling hoses to the radiator. Replace the fan and fan shroud. Reconnect the fan electrical connection.

Fill the radiator with fluid. Check your work to make sure that there are no leaks. (Tools need to be prepared: Screwdrivers, Wrenches, Drain pan).

Note: Do please keep children and pets away when replacing the radiator. Project operation, the vehicle normal temperature 60 to 80 degrees. Add detergent if the tank is too full can take some antifreeze.

1pcs of brand new radiator. CU2310,2310, Engine Rad, Replacement Radiator, 1.03in. RAD2310, CU2173, engine radiator, cooling radiator, air radiator.

1640003140,1640003142,1640003150,1640003151,1640003152. Please verify the item fits your vehicle or not by compatibility. 2 Row Aluminum Radiator For 1990-97 Toyota MR2 MR-2 SW20 2.0 REV1 REV2 REV3 TURB. (Please verify your radiators measurements with the measurements below before ordering). 1X Brand New 2 row Radiator as pictures.

Just the pieces shown in the pictures. The actual products are the same as in the pictures we listed.

Please compare your part to the listed pictures and check the pictures or drawing diagram carefully before purchasing. Professional Installation is Highly Recommended (No Instruction Included).

Radiator Specifications(Der kühler ist kernlage). Please verify your radiator measurements before ordering(Stellen sie bitte vor der bestellung ihre kühlmittelgröße nach). 100% Leak Tested; -Improve 30%-45% Cooling Efficiency; -Built to strict quality control standards; -ISO 9001 certified manufacturing plants; -Good sealing.

We have upgraded our package design to avoid this kind of problem. Our Radiator is made of AA5052 aircraft aluminum. Its different from other sellers T-3303 Series.

In fact, AA5052 series Aluminum is much better than T-3303 series. More than 90% of aftermarket manufacturers use the T-3303 series Aluminum, because it is cheaper and easier to get the material. However, T-3303 aluminum has many disadvantages, such as poor polishing effect, softness, easiness to scratch and corrode, poor heat dissipation effect. If the T-3303 aluminum radiator is operated in high pressure and high temperature for a long time, the leaking problem would occur very soon.

AA5052 Aluminum is an Al-Mg alloy with good corrosion resistance, excellent reliability and cold work ability and strength. The main alloying element of AA5052 is magnesium, which has good forming and processing properties.

This AA5052 Aluminum Radiator is designed to provide maximum cooling efficiency to prevent premature engine failure. Its light-weight, and high-heat transferring aluminum features a tube and fin design that, dramatically increases surface area that enables the heat to dissipate more efficiently. This AA5052 Aluminum Radiator is at least 30%-45% more efficient than stock ones.

Most importantly, it has a much higher capacity for coolant than stock ones, which means that your cooling system will be more efficient and will be more resistant to temperature surges in racing applications. Other international country buyers, depending on your location, items will be sent from the US, Australia and China. All our products are in high good quality, in rare case if an item received was damage or defective, please notify us within 7 days of receipt of it. We will do our best to solve it and satisfy you.

We will arrange for a eplacement to be sent as soon as the item is received by us. Very appreciated for your support.

We will do our best to solve your problem as soon as possible. We appreciate your continued patience and willingness to work with us. Thank you for choosing us and have a great day!

And we will do the same for you automatically! Thank you for your cooperation.